In Dalian extrusion molding production, screw parameters directly affect plasticizing performance, extrusion stability and product appearance. Changes in raw material grade, product cross-section and extrusion speed require corresponding adjustments to screw structure and operating parameters. Proper screw matching is the key to stable production and waste reduction, and also a core part of process commissioning for Dalian extrusion molding.
In the preliminary selection stage, the basic screw structure is determined according to raw material characteristics. Plastics differ greatly in melting properties. PE and PP feature good flowability, so gradient screws are applicable. PVC is heat-sensitive and generally uses equal-pitch variable-depth screws to control shear intensity and avoid material decomposition. Engineering plastics such as PC and PET have high viscosity and require screws with suitable compression ratio and L/D ratio. The L/D ratio is a core index. A low L/D ratio leads to insufficient plasticization and uneven mixing; an excessively high L/D ratio prolongs material residence time and tends to cause thermal degradation. This is the first step for screw matching in Dalian extrusion molding.
The compression ratio is selected based on raw material density and foaming requirements. It refers to the ratio of screw channel volume between the feed section and metering section, which compacts, degasses and melts materials. Higher compression ratios are adopted for crystalline plastics while lower ones for amorphous plastics. For foamed extrusion and filled modified materials, the compression ratio shall be recalculated to prevent cell rupture and filler agglomeration. If the compression ratio of the existing screw fails to match the raw material, simply raising the temperature can hardly remedy the problem, resulting in unstable output, internal voids and surface pitting.
Differentiated configuration is adopted for pitch, channel depth and shear elements. The feed section has deeper screw channels for stable feeding; powder and highly filled raw materials impose higher requirements on the conveying capacity of the feed section. The melting section provides shear plasticization, and barrier sections, pins or mixing heads can be equipped according to mixing demands. The metering section has shallow, high-precision channels to stabilize extrusion flow. For high-speed thin-wall products, the metering section is designed for pressure stabilization; for thick-wall and modified materials, additional mixing elements are used to disperse additives evenly.
Operating process parameters shall be matched in coordination with the screw structure. After the screw is confirmed, set main screw speed, barrel zone temperatures and back pressure. The rotating speed shall fit the screw capacity. Excessive speed results in insufficient residence time and poor plasticization; too low speed causes overheat accumulation due to long residence time. Back pressure is adjusted through die resistance. Higher back pressure strengthens shear and mixing yet reduces output. For the same screw, adjust temperature, speed and back pressure preferentially when changing materials instead of replacing the screw frequently. Production lines with frequent material switching can be equipped with spare screws.
Verification shall be carried out against product specifications and extrusion capacity. Small-cross-section thin-wall profiles and film extrusion adopt small-diameter screws with high precision requirements for the metering section. Pipes, thick plates and large-cross-section profiles use large-diameter screws to guarantee throughput. When higher capacity is needed, calculate the theoretical extrusion output of the screw, which shall exceed the order demand to reserve adjustment margin. Meanwhile, match the barrel, die and cooling sizing table, and align screw conveying flow with die discharge capacity as much as possible to avoid pressure buildup or material interruption.
Machine trial and record keeping are required. After installing a new screw or changing raw materials, conduct low-speed trial extrusion first, monitor melt pressure, melt temperature and discharge uniformity, inspect product dimension and surface condition, and optimize parameters step by step. Record screw model, L/D ratio, compression ratio, as well as corresponding raw material, rotating speed, temperature and back pressure to build process files. Regularly inspect wear of long-running screws. Worn screw flights degrade conveying and shear performance; parameter adjustment can hardly restore stability, so repair or replacement shall be assessed.
In summary, matching screw parameters for Dalian extrusion molding starts with raw material types to determine the L/D ratio, compression ratio and structural form, followed by coordinated adjustment of operating parameters including speed, temperature and back pressure. Verified through trial production, the scheme balances plasticizing quality, stable extrusion and production efficiency.







